do not scale from this print .120 ref 3.05 .100 ref (typ) 2.54 .050 ref 1.27 .080 2.03 ref "c" ref (typ) (see note 5 & table 3) .145 ref 3.68 "a" "a" "b" "b" 'd' 01 02 fig. 1 through hole/straight modified (shown: sfml-125-x1-xxx-d) sfml-1xx-xx-xxx-d-xxx no of positions -05, -07, -10 thru -50 (per row) row specification -d: double row (use sfml-xx-d-x) lead style -01: through hole (use c-44-01-xxx, see fig 1, sht 1) -02: surface mount (use c-44-02-xxx, see fig 3, sht 2) -03: straight modified (use c-44-03-xxx, see fig 1, sht 1) -l1: through hole (low insertion) (use c-61-01-xxx, see fig 1, sht 1) -l2: surface mount (low insertion) (use c-61-02-xxx, see fig 3, sht 2) -l3: straight modified (low insertion) (use c-61-03-xxx, see fig 1, sht 1) -t1: through hole (phos bronze) (use c-119-01-xxx, see fig 1, sht 1) -t2: surface mount (phos bronze) (use c-119-02-xxx, see fig 3, sht 2) plating specification -s: selective -p: gold flashed palladium nickel -f: flash selective gold -h: heavy gold -l: light selective gold -stl: selective gold/ tin-lead (only available on -02 and -l2 leadstyles) -sm: heavy selective gold, matte tin tail -lm: light selective gold, matte tin tail -fm: flash selective gold, matte tin tail (leave blank for standard and use sfml-xx-d) -a: alignment pin (use sfml-xx-d-a) (see fig 5, sht 3) -lc: locking clip (see fig 7, sht 3) (use (2) lc-05-tm & sfml-xx-d) (see note 9) -p: pick & place pad (see fig 6, sht 3) (use ppp-02) (not available in 5 pos) -tr: tape & reel packaging (n/a with -x1 and -x3 lead style, see fig 2, sht 1) -k: polyimide film pad (use k-500-300)(see fig.4, sht. 2) -sn: solder nail (use sfml-xx-d-sn & wt-27-01-t) (see fig 8, sht 4) (available on -x2 lead styles only) -sn2: solder nail for .093 board (use sfml-xx-d-sn & wt-27-02-t) (see fig 8, sht 4) (only available with -02, l2, and t2 lead style. not available with -a, -lc options) options (see table 1) "b" ref .180 4.57 ref .110 2.79 ref (no of pos x .050 [1.27]) + .015 [.38] ref (no of pos x .050 [1.27] + .155 [3.94] ref .035 ref (typ) 0.89 (see table 1) "a" (typ) 1 max sway (no of pos x .050 [1.27]) - .050 [1.27] section "a"-"a" c3 c4 c2 .050 ref 1.27 section "b"-"b" .065 ref 1.65 .005 ref 0.13 .050 1.27 (typ) 2 max toe sfml-xx-d pos. 1 user direction of unreeling fig. 2 -tr: tape & reel packaging (alternate keying option shown) see note 6 .060 1.52 ref .020 0.51 ref detail 'd' alternate construction c c1 c8 ab sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: .050 [1.27] x .050 [1.27] locking socket assembly by: sfml-1xx-xx-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 4/19/99 4 1 sheet scale: 2:1 insulator: vectra e130i contact: becu phos bronze c:\enterprisevault\dwg\misc\mktg\sfml-1xx-xx-xxx-d-xxx-mkt.slddrw notes: 1. represents a critical dimension. 2. coplanarity: .004 [.10] for pos. 10 thru 26 .006 [.15] for pos. 27 thru 50 3. minimum pushout force: .5 lb. 4. maximum allowable bow: .002 inch/inch [mm/mm] after assembly. 5. positions -05 and -07 will have only one clip at dimension shown and will not have polarization notch; positions -10 through -24 will have only one clip at dimension shown; positions -25 through -34 will have two clips at dimension shown; positions -35- through -50 will have three clips: two at dimension shown & one centered on insulator. 6. see notch for proper orientation. 7. pins can be oriented in any direction; both rows must facw same way. 8. maximum pin height variation between any two rows: .003[.08]. 9. due to the high amount of insertion force needed, the Clc option is not compatible with auto placement. samtec recommends manual placement for all assemblies with the Clc option." 10. tube parts with notch toward arrow. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision ab
"m" "p" .1575 .0050 4.000 0.127 fig. 4 -k: polyimide film pad option (shown: sfml-110-x2-x-d-k) (alternate construction shown) note: "m" = used measured dimension (ref) "p" = {("m" - .1575 [4.000]) /2} .020 [.51] .190 4.83 "c" "c" (no of pos x .050 [1.27]) - .050 [1.27] (tol accum .005 [.13] over 50 pos.) (typ) 2 max sway c-xx-x2-xxx c7 .185 - .005 + .002 4.70 - 0.13 + 0.05 .165 ref 4.19 +4 see note 2 section "c"-"c" -2 c6 fig. 3 -x2: surface mount (same as fig. 1, unless otherwise stated) c5 sheet of by: sfml-1xx-xx-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 4/19/99 4 2 sheet scale: 4:1 revision ab c:\enterprisevault\dwg\misc\mktg\sfml-1xx-xx-xxx-d-xxx-mkt.slddrw .050 [1.27] x .050 [1.27] locking socket assembly 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
(no of pos x .050 [1.27]) + .125 [3.18] ref .050 ref 1.27 (no of pos x .050 [1.27]) + .075 [1.91] ref fig. 5 -a: alignment pin option (same as fig. 1, unless otherwise stated) (alternate construction shown) sfml-xx-d-a .050 ref 1.27 .056 ref 1.42 .065 1.65 (no of pos x .050 [1.27]) + .075 [1.91] fig. 7 -lc: locking clip option (same as fig. 1, unless otherwise stated) (alternate construction shown) sfml-xx-d lc-05-tm .010 ref 0.25 .062 1.57 (see table 2) "a" .010 [.25] locking tab .394 ref 10.01 ppp-02 fig. 6 -p: pick & place pad option (same as fig. 1, unless otherwise stated) (alternate construction shown) .225 5.72 ref pt-1-24-13-09 pt-1-24-14-09 ( see note 9) samtec anti-static samtec anti-static pt-1-24-15-09 package parts in tubes as shown sheet of by: sfml-1xx-xx-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 4/19/99 4 3 sheet scale: 3:1 revision ab c:\enterprisevault\dwg\misc\mktg\sfml-1xx-xx-xxx-d-xxx-mkt.slddrw .050 [1.27] x .050 [1.27] locking socket assembly 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
"b" ref (no of pos x .050[1.27]) + .185[4.70] ref (no of pos x .050[1.27]) + .085[2.16] 2 max sway (typ) "d" "d" fig. 8 -snx: solder nail option (shown: sfml-125-02-xxx-d-sn (same as fig. 1, unless otherwise stated) (only available on -x2 lead styles) sfml-xx-d-sn wt-27-xx-t c l c10 .026 0.66 ref (2 plcs) flush to .005[0.13] above section "d"-"d" c l c9 table 3 option "b" -sn .066[1.68] sn2 .101[1.80] sheet of .050 [1.27] x .050 [1.27] locking socket assembly by: sfml-1xx-xx-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing bratcher 4/19/99 4 4 sheet scale: 4:1 revision ab c:\enterprisevault\dwg\misc\mktg\sfml-1xx-xx-xxx-d-xxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
